Mcdata 4400 Serial Port Settings

To help reset the IP manageability please follow the steps below: 1. Set up a null modem (RS-232) cable to the maint port on the back of the switch.2. Using Hyperterminal, make a connection using the COM port with the following settings:a. Bits per second 57600 b.

Data Bits 8c. Parity Noned. Stop Bits 1e. Flow Control None.3. Then use the password `level-2', it should show as all x's.4. Press enter, and you will see a SSP0 (or similar) prompt.5.

McDATA Sphereon 4400 Fabric Switch. You can begin with as few as 8 ports and grow capacity in 4-port increments (leveraging McDATA's industry-first FlexPort. Need some help as we are unable to ping/telenet or connect through web interface to a Mcdata 4400. Make a connection using the COM port with the following settings.

Now type the command ipconfig6. You will see the current IP address, subnet and gateway.7. Unplug the Ethernet cable from the switch and using the command ipconfig again enter ipconfig xxx.xxx.xxx.xxx yyy.yyy.yyy.yyy zzz.zzz.zzz.zzz where xxx.xxx.xxx.xxx is the IP address, yyy.yyy.yyy.yyy is the subnet, zzz.zzz.zzz.zzz is the gateway, and change the IP address by one number.8. Then change it back using the same command. If that does not resolve issue please see emc133068 -Jeff. My 1760 router is not working correctly.

I have given an IP to the eth0/0, VLAN1 (with 4 port WIC), and two servers off of a 2950 switch cabled to eth0/1 in VLAN1 of the router. All 2950 switch ports are also in VLAN1. Router eth0/0 is set to access mode and everything seems to be working fine internally. At this point ip host-routing is enabled, ospf is enabled with: x.x.35.11 0.0.0.0 area 0 (eth0/0) x.x.36.225 0.0.0.0 area 0 (VLAN1) x.x.36.226 0.0.0.0 area 0 (server 1) x.x.36.227 0.0.0.0 area 0 (server 2) subnet mask for everything is /24 I have set ACL for VLAN1 and eth0/0 inbound and outbound both to permit IP any any. (I just want it to start working). Firewall is not enabled. VPN is not being used.

I have firewalls up on both servers, so I am safe when it starts working. I just want one less headache in the way right now. Router port eth0/0 can be pinged from the internet. NO x.x.36.y IP's can be pinged from outside the router. From either of the servers (x.x.36.226 227), either server can be pinged, VLAN1's IP can be pinged (x.x.36.225) and router eth0/0 (x.x.35.11) can be pinged but nothing can go beyond the router eth0/0.

When logged into the router via telnet, ssh, https etc. Via eth0/0 x.x.35.y (management, outside). VLAN1 and both servers, all three of which are x.x.35.y can be pinged. So, this thing has to be routing packets for data to be transfered between the x.x.35.y and x.x.36.y subnets. What do I do now to trouble-shoot why the servers cannot route data out beyond router eth0/0 or why data cannot be routed beyond eth0/0 from the outside in?

Kasak serial on dd national wiki. This small network exists within a larger pre-existing network. I brought up ethereal today to see what was going on. I do not believe ethereal can sniff RIP data however, the only ospf traffic I saw appeared to be my own and there was TONS of ARP traffic.

The larger network I am within in this building is all segmented /24 from a class B. All gateways are x.x.Y.254. DNS for the entire larger network is x.x.1.1. Also here is my edited sh run no aaa new-model ip subnet-zero ip host-routing!

Ip audit notify log ip audit po max-events 100 ip domain name x.y.edu ip name-server x.x.1.1 no ftp-server write-enable! Interface FastEthernet0/0 description $ETH-WAN$ ip address x.x.35.11 255.255.255.0 ip access-group sdm_fastethernet0/0_in in ip access-group 101 out speed auto full-duplex! Interface FastEthernet0/1 no ip address! Interface FastEthernet0/2 no ip address shutdown! Interface FastEthernet0/3 no ip address shutdown!

Interface FastEthernet0/4 no ip address shutdown! Interface Vlan1 ip address x.x.36.225 255.255.255.0 ip access-group 100 in ip access-group sdm_vlan1_out_100 out!

Router ospf 1 log-adjacency-changes network x.x.35.11 0.0.0.0 area 0 network x.x.36.225 0.0.0.0 area 0 network x.x.36.226 0.0.0.0 area 0 network x.x.36.227 0.0.0.0 area 0! Ip default-gateway x.x.35.254 ip classless! No ip http server ip http secure-server ip ospf name-lookup! Ip access-list extended sdm_fastethernet0/0_in remark SDM_ACL Category=1 permit ip any any ip access-list extended sdm_vlan1_out remark SDM_ACL Category=1 permit ip any any ip access-list extended sdm_vlan1_out_100 remark SDM_ACL Category=1 permit ip any any! Access-list 100 remark SDM_ACL Category=1 access-list 100 permit ip any any access-list 101 remark SDM_ACL Category=1 access-list 101 permit ip any any!

Line con 0 line aux 0 line vty 0 4 password ****** login! No scheduler allocate. Hi, I'm trying to connect an UCS to a SAN based on McData SAN switches. I configured the WWN pools and the vHBAs. The SAN Admin told me, NPV is on the port activated and NPIV is supported. On the swicthes, my WWPNs are visible and the SAN Admin configured the zoning and the presentation already.